Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Antelope
Gate repair in Antelope usually falls into two camps: a wood or iron gate that’s sagging, sticking, or binding, or an automatic operator that won’t open, won’t close, or grinds when it tries. Most calls we get from the 95621 and 95843 ZIPs are fixed the same visit because we carry the hinges, latches, control boards, and sensors that Antelope’s aging tract gates actually need. If your gate is failing somewhere along Antelope Road, Walerga Road, or in the neighborhoods off Elverta, call us at (833) 620-4636. Rodney Caldwell runs the crew, and he’s been working gates in this part of Sacramento County long enough to know exactly what fails on a 1990s builder-grade setup.
Why Gate Repair Del Paso Park Is Antelope’s Preferred Gate Repair Company
We’re a gate-only shop. That’s the whole thing. We don’t split our attention between fences, garage doors, and “oh sure we can do that too.” Every technician at Gate Repair Del Paso Park works on gates, automation, and access hardware every day, and every part in the van is there for a gate. When an Antelope homeowner calls about a Mighty Mule keypad that won’t sync or an Elite ram that’s lost its travel limits, the person who shows up has that board in the truck. That’s the difference between one visit and three.
Antelope residents see us a lot because this is a master-planned suburb where the development pattern repeats itself. The gates we repair on one block of misting-cooled tract homes on the north side are typically the same gates we repaired three streets over last month. That repetition isn’t boring to us. It means we know what’s about to fail before we even pull up. Rodney and the crew have rebuilt enough 1980s and 1990s gate hardware in 95621 to spot a thin galvanized hinge on its way out before the homeowner notices the sag.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Iron Gate Repair in Antelope
Iron Gate Repair in Antelope means one of two things: a decorative wrought-iron or ornamental steel gate that’s rusting at the welds or pulling away from its hinge post, or a heavy iron driveway gate that’s too much for its original builder hardware. We cut out rust on the bottom rails, weld cracked pickets back into square, and re-hang the gate on heavier barrel hinges when the originals have wallowed out. Antelope’s summer sun bakes the finish off iron gates over a few seasons, and winter tule fog plus sprinkler overspray will rust any bare steel that’s exposed. We repair, grind, prime, and paint the gate before it gets thin enough to fail.
Weld and Rust Repair
Most iron gates in Antelope fail from the ground up. The bottom rail sits in wet grass or under an irrigation spray pattern, the paint wears off, and rust ate into the tubing long before anyone noticed. We cut out the bad section, weld in a matching steel patch, and re-coat it. A typical bottom-rail and picket repair in Antelope runs $280 to $550 depending on how far the rust got.
Hinge Replacement and Gate Realignment
A heavy iron gate on stamped builder hinges will sag. It always does, eventually. We swap those thin hinges for greasable bearing hinges rated for the gate’s actual weight, then re-square the gate on the post and reset the latching line. In Antelope, a single-side hinge replacement with realignment runs $190 to $360, and it usually eliminates the drag and the creak in the same visit.
Sliding Gate Repair in Antelope
Sliding Gate Repair in Antelope is the bread and butter of the corner-lot streets. The original chain-link slide gates on 25 to 35 year old homes are honest workhorses, but they jump their rollers, chew up the rack, and fight operators that were bolted to a post footing that settled years ago. We reset posts, re-hang the sliding panels, rebuild rusted tension bands, and get the operator’s rack and pinion running true again. A typical sliding gate tune-up, including track alignment and operator limit adjustment, runs $240 to $480 in Antelope.
Track and Roller Rebuilds
When a slide gate drags or bounces, the question is always roller, track, or post. On Antelope corner lots we usually find all three involved: the post footing heaved a quarter inch, which dropped the track, which wore the rollers flat on one side. We fix the whole stack. Replacing worn rollers and re-aligning the track typically runs $180 to $340.
Operator and Rack Repair
The operator on a chain-link slide gate wears out because it’s been grinding against the same damaged rack for years. We replace stripped-out rack sections and re-time the operator’s limits so the gate stops soft instead of slamming the post. On a LiftMaster or FAAC slide operator in Antelope, figure $290 to $550 for rack work, limit reset, and a new battery if the old one has died.
On a corner-lot tract home off Antelope Road, our crew answered a sliding gate repair call where the original chain-link slide gate had jumped its track and the gate operator’s rack and pinion was grinding against a hinge post that had quietly heaved out of its post footing. We reset the footing, corrected the sag, and fitted a LiftMaster operator with a working loop detector and safety photocell before calling it done.
Trusted Brands We Service in Antelope
We work on your brand, not just gates in general. Factory-familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, we stock the boards, remotes, and sensors that Antelope’s tract homes actually use. That Mighty Mule on the side gate off of Walerga? We carry its control board. That LiftMaster on a corner-lot slide gate? We carry the limits and the receiver. From a stuck residential gate to a commercial FAAC operator, we’ve seen it. Repair-first means we fix what’s there before recommending anything new, and multi-brand fluency means we don’t push a replacement just because the local installer doesn’t stock the part.
Common Gate Repair Problems We See in Antelope Homes
- Builder-grade hinge and latch failures. Antelope’s tract homes were built with the same thin galvanized hinges and stamped latches block after block. When one model starts failing, we see the same failure on the same model three streets away within months.
- Wood panels drying and binding at the hinge post. Intense Sacramento Valley sun pulls moisture out of 25-year-old redwood and fir gates until they warp. The warp binds the gate at the hinge post and the opener strains against it every cycle.
- Corner-lot slide gates rusting at the rails. Winter tule fog and constant sprinkler overspray rust the bottom rails of chain-link slide gates on Antelope’s corner lots. Rusted rails jump rollers, which chews up the rack, which kills the operator.
- Operator boards and sensors glitching in heat. The same summer heat that warps wood gates also cooks operator control boards mounted on south-facing posts. Photocell eyes get hazy from dust and irrigation film, and the gate starts reverting or reversing mid-cycle.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Antelope, CA
A typical gate repair visit in Antelope runs $190 to $550, and the exact price is quoted and agreed before any work starts. Hinge replacement and realignment runs $190 to $360. Weld and rust repair on an iron gate runs $280 to $550. Sliding gate track and roller work runs $180 to $340, and operator repair including rack and limit adjustment runs $290 to $550. What moves the price is the weight of the gate, how much of the hardware has been run past its failure point, and whether we’re matching into a home-automation system. Estimates are free. Call (833) 620-4636 and we’ll put numbers on what you have.
We Also Serve Cities Near Antelope
Our Gate Repair team runs Antelope, Foothill Farms, Citrus Heights, North Highlands, and Roseville every week. If you’re in one of those neighboring ZIPs and your gate is sagging or your operator won’t respond, same crew, same stocked van. Learn more about our specific work here: Gate Repair in Antelope.
Serving Antelope, CA – Our Local Coverage Area
We’re based in the Antelope area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Antelope
Antelope’s master-planned tracts from the 1980s and 1990s used the same builder-grade gate hardware across entire model-home blocks, so the thin galvanized hinges and stamped latches all fail on the same schedule. A technician who knows the floor plan can predict where the hardware is already failing just by knowing which model home it is. If your neighbors are all getting their gates re-hung this year, yours is likely next. Call (833) 620-4636 and we’ll tell you honestly whether it’s time.
Usually both, but the hinge post fails first on Antelope tract homes. The post footer was set shallow and the gate’s weight has been pulling it forward for 25 years, so the gate sags no matter how many times someone tightens the hinges. We check the post for movement, re-set or re-concrete it if needed, then straighten or replace the panel. A post reset plus hinge replacement in Antelope runs $290 to $480, and we’ll show you the price before we start. Call (833) 620-4636 for a free estimate.
Yes. We repair and rebuild those constantly. The original chain-link slide gates on corner lots in 95621 and 95843 are hitting the end of their track and roller life, and we carry the replacement rollers, rack sections, and operator parts to keep them running. If the post footing has settled, we fix that too. A sliding gate track, roller, and operator tune-up in Antelope runs $240 to $480. Call (833) 620-4636 and we’ll come look at what’s jumping.
Yes, and this isn’t a paperwork requirement. Under UL 325 safety standards, automatic gate operators must have an entrapment-protection device: photo eyes, an edge sensor, or a current-sensing reverse that stops the gate if something is in the way. If your gate closes on a child, a pet, or a car, the liability and injury issues are serious, so we check the sensors on every gate repair visit. A sensor replacement or re-alignment in Antelope runs $120 to $260. Call (833) 620-4636 and we’ll test what’s installed.
LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Gate Repair Del Paso Park carries parts for all nine, so we typically repair the operator that’s already on the gate rather than selling a new one. If your operator is a brand we didn’t list, call anyway. (833) 620-4636.
Ready to Fix the Gate? Call Us.
The longer a sagging gate runs, the more it costs to fix. Hinges wallow out, the operator burns itself up, and a heavy iron panel takes a post over with it. Antelope homeowners and property managers can reach Rodney and the crew directly at (833) 620-4636 for a free estimate on any gate repair, electric gate repair, or new gate installation. Quotes are given and agreed before any work starts, and we’ll tell you straight what needs fixing and what can wait. Same number covers 95621, 95843, and the surrounding Sacramento suburbs.
Written by Rodney Caldwell, Owner at Gate Repair Del Paso Park, serving Antelope and the Sacramento Valley.